|
Bullard TIx Thermal Imager
|
|
 Technical
Specifications |
| Carrying Case | |
|
Dimensions |
18.5" x 15" x 7.5" |
|
Weight - Empty |
Approx. 8 pounds |
| Overall TI Unit | |
|
Weight |
With battery 5.75 pounds Without battery 5 pounds |
|
Dimensions |
Height : 12 " Length : 10 " Width : 6 " |
|
Heat Test |
650°F (343°C) for 5 minutes |
|
Impact / Drop Test |
Dropped 3 consecutive times from 3 feet with no noted physical or operational damage |
| Casing | |
|
Shell Material |
Ultem Thermoplastic |
|
Sealing |
Silicone |
|
Strap Material |
Kevlar & Leather |
|
Display Cover |
Polycarbonate |
|
Heat Test |
650°F (343°C) for 5 minutes |
|
Impact / Drop Test |
Dropped 3 consecutive times from 3 feet with no noted physical or operational damage |
| Core / Detector | |
|
Type |
Uncooled Ceramic Focal Plane Array Detector |
|
Resolution |
320 x 240 array |
|
Sensing Material |
Barium Strontium Titanate Ceramic (BST) |
|
Spectral Response |
8 - 14 Microns |
|
Thermal Stabilization |
Thermoelectric Cooler |
|
Update Rate |
30 Hz |
|
Temperature Sensitivity |
0.05° C |
|
Video Output |
RS-170 Signal (1.4 volts P-P) |
|
RS-170 Signal |
|
| Lens | |
|
Material |
Germanium |
|
Lens Size |
18 mm |
|
Field of View |
55° |
|
Distances Optimal Focus |
3 feet (1 meter) to infinity |
| Electrical System | |
|
Power Source |
NiMH Rechargeable Battery |
|
Output |
10V |
|
Capacity |
1100 mA.hr |
|
Operating Time |
1.5 hours |
|
Charger Single Battery |
Single Battery, 120 VAC or 12 VDC |
|
Switch Cycle Test |
1,000,000 cycles |
|
Battery Life |
1,000 charge cycles |
|
Battery Weight |
0.75 pounds |
| Display | |
|
Type |
Liquid Crystal Display (LCD) |
|
Size |
4" |
|
Dot Pitch |
.259mm (V) x .210mm (H) |
|
Dot Format |
234 X 380 Dots |
|
Pixels |
89,622 |
|
Pixel Configuration |
R-B-G Delta Configuration |
|
Display Method |
TFT Active Matrix |
|
Input Signal Level |
1.0V P-P (Positive) 75 Ohm |
|
Back Light |
CCFT Backlight |
| Transmitter | |
|
Mounting |
Internal |
|
Signal Type |
Analog |
|
Antenna Type |
Dipole |
|
Transmitting Frequency |
2.4 GHz |
|
Power Output |
400 mW |
|
Power Supply |
Internal |
|
Power Consumption |
2.8 W |
|
Frequency Selection |
2 Channel Switch |
|
FCC License |
Part 90 |
| Receiver | |
|
Power Requirements |
11-14.5 VCD (Center Positive) |
|
Power Consumption |
250 mA |
|
Power Input |
Coaxial 2.1mm x 5.5 mm Center- Positive Connector |
|
Power Supply |
120 VAC or 12 VDC |
|
Operating Temperature |
14° F to 122° F |
|
Signal Type |
Analog |
|
Receiving Frequency |
2.4 GHz |
|
Video Outputs |
Two (2) 75-ohm 1-volt P-P video outputs (female BNC) |
|
Range Unobstructed Line-of-Sight |
Up to 10 miles |
|
Range Obstructed Line-of-Sight |
300 feet |